關于我們

U型玻璃的建筑設計的分類

2019-04-11 13:47

A.U型玻璃按表面處理方式不同,有普通壓花玻璃、彩色玻璃等,設計選用時除普通壓花玻璃外,選用其余玻璃應予注明。

B.U型玻璃屬不燃燒材料,如有特殊要求時應按有關規范進行設計。

C.U型玻璃分類:

—按顏色分:有色的和無色的。

—按表面狀態分:有平滑的和帶花紋的。

—按強度分:有鋼化、貼膜、保溫層

—按規格分:有鋼化、貼膜、保溫層

D.U型玻璃屬不燃材料,如有特殊要求時按有關規范進行設計。

E.U型玻璃兩翼的朝向測試結果表明兩翼向迎風面內,強度高于兩翼背風面。

F.U型玻璃按造型及建筑使用功能分別采取以下組合方式:

G.U型玻璃隔墻長度大于6000,高度超過4500時,應核算墻身的穩定,采取相應的措施。

H.U型玻璃用于濕度較大的房間且室內外溫差較大時,應處理好玻璃表面露水的排泄及下滴問題。

I.U型玻璃用于圓型墻及屋面時,曲率半徑不應小于1500。

zbc0df2545a03192Bac0c71f640159d805[1].jpg


A. U glass according to the surface treatment method, there are ordinary embossed glass, stained glass, etc.. In addition to ordinary embossed glass, the selection of the rest of the glass should be noted.
B.U glass is a non-combustion material and should be designed according to relevant specifications if there are special requirements.
C. U type glass classification:
By color: colored and colorless.
By surface status: Smooth and patterned.
-By strength: there is a toughening, film, insulation layer
-According to specifications: there are steels, film, insulation layer
D. U glass is a non-flammable material and is designed according to relevant specifications if there are special requirements.
The orientation test results of the E.U-type glass wings show that the strength of the wings is higher than the leeward sides of the wings.
F.U glass adopts the following combination methods according to its shape and architectural function:
G.U-type glass partitions with a length of more than 6,000 and a height of more than 4,500, the stability of the wall body should be calculated and corresponding measures should be taken.
H. U glass is used in large humidity rooms and when the temperature difference between indoor and outdoor is large, the excretion and droplet of glass surface dew should be handled.
When I.U glass is used for round walls and roofs, the radius of curvature should not be less than 1500.